Super Lite

Buying Guides

How to Safely Replace A Ceiling Light

How to Safely Replace A Ceiling Light

by ·

Ceiling lights are a must-have feature in any room. Whether you don’t like the previous homeowner’s taste or you’re just ready for an update, ceiling lights can revitalize your home space. It may be even easier than you think–just follow these steps to safely switch out those old light fixtures for a new look.

What you’ll need:

  • Screwdriver
  • Step ladder
  • Voltage detector 

You may also need:

  • Wire cutters
  • Wire strippers
  • Pliers
  • Painter’s tape
  • An extra set of hands 

Part 1: Remove Old Fixture

Step 1: Turn off power

Shutting off the electricity is important to your safety. Locate the switchboard for the room you are working in and flip the switch. If you’re not sure where the switchboard is, check the basement or garage. It might also be in the front of the house or near the entrance.

Once you’ve flipped the switch for the room with the ceiling light, go back into the room and flip the switch a few times to make sure the power is off. Then, leave the light switch in the off position. Make sure you lock the circuit box or leave a note indicating that you are working. 

Step 2: Remove cover and bulbs

Use a stable step ladder to reach your ceiling light. Hold the cover, or the visible, outside piece of the light fixture, in place with one hand. Loosen the screws with a screwdriver in the other. (For heavy or large fixtures, it’s best to have someone else hold on while you work on the screws.

Once the cover is removed, unscrew the light bulbs and set them aside.

Step 3: Lower the fixture base

With the cover removed, you will be able to see the base–the part of the light fixture that attaches directly to the ceiling. Typically, the base will have tabs or nuts and screws securing it. Loosen the nuts or screws, then lower the base to access the wiring (In the rare case you’re unable to find the screws, search for the installation manual online. You can also take a picture of your base and bring it into our showroom – we’ll take a look and help you figure it out!)

Until you have disconnected the wiring, you will want to lower the base but not remove it completely—an easy way to do this is by securing it with painter’s tape or having someone else hold it in place.

Step 4: Disconnect the wires

Once you have uncovered the space behind the old light fixture, there should be a junction box where wires are connected and stored. Start by removing the caps or tape covering the wire connections. The caps will come off when twisted counterclockwise.

 Pro Tip: Take a picture beforehand so you can remember exactly how everything was put together. 

Part 2: Connect the Wiring

Step 1: Test voltage

Test each exposed wire by touching it with the tip of your voltage detector. 

If the voltage detector lights up, there is a current running through, and the wire is unsafe to touch. Double-check your circuit box and ensure the switch is still flipped. 

Once you’re sure there is no electrical current, you are safe to continue working with the wires.

Untangle the wires and detach the fixture from the ceiling completely. Either hand off to someone below or carefully carry it down the ladder.

Step 2: Check wires

Frayed wires can be hazardous -if there is any fraying on the end of the wires, trim them down with wire cutters. Then, strip off any insulation on the outside with wire strippers. You only need to strip about ½ inch of insulation for the wire connection.

Pro Tip: Check your new fixture’s installation recommendations carefully. If you’re installing a heavy fixture such as a ceiling fan or chandelier, you may also need to install an additional support in the ceiling. 

Step 3: Match and Attach

Electrical wires are color-coded. Black or red are hot wires, white is neutral, and green or bare copper are ground wires. A grounding wire sometimes connects to a grounding screw instead of another wire. Look for a matching wire in your ceiling for each wire in your fixture.

Twist together each matching wire. Either by hand or with pliers, hold the exposed ends side by side with one hand and twist with the other. (This is where your picture of the original fixture’s wiring comes in handy.)

Now that the wires are connected, it’s important to cover the exposed ends again. Screw the wire caps on by twisting clockwise over the connected ends until they hold the wires tightly in place. If your original fixture didn’t have wire caps, you can use electrical tape as well.

Make sure to check the owner’s manual for specific instructions—for example, you might have an extra red wire that connects to a black wire. If you don’t have any instructions, generally you will be fine with just matching the correct wire colors.

Part 3: Install New Fixture

Step 1: Replace junction box

With all your wiring safe and sound, the junction box is ready to be put back into place. Tighten the screws securely against the bracket until  Fold the wires up into the box so they will be hidden behind the ceiling light.

Step 2: Attach new fixture

There are several different ways your new light fixture base could attach to the ceiling—these are the most common ways. As always, check the owner’s manual for anything specific or unique about your light.

Securely attach the light base by positioning it over the mounting screws. Place a metal nut on each screw and twist by hand until they are tightly holding the base in place.

If the fixture has a mounting bracket, connect the mounting bracket to the junction box first, then hang the base over the screws.

If it’s a keyhole shape, adjust the base so the screws slide into the smaller grooves and then tighten the screws with a screwdriver until they are holding the base securely.

Step 3: Install light bulbs

Now that your base is set, it’s time to add the light bulbs. Make sure you have the correct wattage—the fixture typically indicates its maximum wattage on the package or owner’s manual. 

When choosing which bulbs to use, the lower the wattage the safer. Most light fixtures are safe with up to 60 watt incandescent bulbs. You may also want to consider more eco-friendly choices, such as CFL or LED bulbs. These options have lower wattage but produce the same amount of lighting, saving you money on electricity in the long run.  

Test the bulbs by turning the electricity back on—flip the switch on the circuit breaker then turn on the room light switch. If it is flickering, dim, or not turning on at all, turn the electricity off again and check everything—look for loose connections or mismatched wires. If your lights are bright and solid, you are ready for the final step.

Step 5: Attach cover

Flip the light switch and circuit breaker back off before installing anything else. Take your light fixture’s shade, cover, or top and climb back up the ladder. Attach it to the base by twisting screws or attaching pieces until everything is tight and secure. If it’s a hanging light, make sure it’s at the proper height before finishing your work. Every light has different connecting components, so check your owner’s manual and just make sure it’s snug.

And there you have it, your guide for installing a new, updated ceiling light. Now that you know how to install it, make sure to visit our showroom to choose the perfect fixture for your ceiling!

Gorgeous Nature-Inspired Rooms You’ll Want to Escape To Immediately

Gorgeous Nature-Inspired Rooms You’ll Want to Escape To Immediately

by ·

When you’re designing your house, finding inspiration is key. Taking a step outside can give you a fresh perspective – there’s no better inspiration than mother nature herself!  No matter what space you’re working on, drawing from the beauty of nature will make your home feel like paradise.

The combination of earth tones and natural materials in these rooms almost makes them feel more like they should be in National Geographic than a home decor magazine – and we mean that in the very best way possible. 

Bathrooms

Picture yourself after a long day of work. You’re exhausted, and what you need more than anything is a moment to yourself. You finally get some uninterrupted time to sit in the warmth of the tub and it feels good. The anxiety melts away. Your bathroom can be a natural refuge from your stress. When you put a little effort into your bathroom, it’ll pay off!

The owner of this room has a green thumb that brings the whole room to life. To complement the plants, they chose a macrame chandelier that’s uniquely fitted for this bathroom. Warm wood and wicker also feel right at home in this organic space. The black furniture and tub ground the look, bringing an effortless cohesiveness. You’d have a hard time feeling anything but relaxed here.

This light and airy space incorporates natural materials like wicker and terracotta pots. The foolproof combination of warm wood tones, green plants, and neutral, natural colors will always leave you feeling like you’re stepping into an oasis! This room is definitely a no-interruption zone.

If it was possible (or ethical) to steal a bathtub, we’d be walking out of this bathroom hauling this one! The wood exterior is a nature enthusiast’s dream base for relaxation. The twinkling lights behind it are also a charming touch to give the bath a glow. 

Living Rooms

The living room is the main hub of the house. It’s where work, relax, and entertain guests – you live here. Whether you choose a paired back approach or go full maximalist and pull out all the stops, make sure to include some natural materials to ground yourself and make the living room feel more like home.

Neutrals are the star of the show in this living room. We love the texture the pendant light brings and how it coordinates with the mirror frame and the accessories in the room. The color palette may be limited, but each piece works together to create a neutral haven where texture is the star of the show. 

This nature-inspired design would work well in a space of any size. When you’re strapped for square footage, picking a smaller couch that will still accommodate your needs is a smart choice. A pendant light also shows creativity since it won’t take up any extra floor space. It’ll give you the ambiance for an intimate conversation or some light for reading. The texture of the wicker and wood here is also stunning. Adding burnt orange brings a tiny pop of color to make you feel extra happy!

This colorful living room is oozing with style! Who said organic design has to be boring? We can’t help but feel insanely jealous of whoever owns this room. Everything here – the colors, textiles, plants, and warm wood furniture – is to die for. Don’t be afraid to go bold and bright if it makes you happy. This is a living room anyone would be lucky to come home to!

This living space uses nearly all natural materials and earth tones in its design to make a cozy conversation space. From the wood ceilings to the stone accents, the textures here are immaculate. Everything feels warm and welcoming. A wood ceiling fan matches all the decor and will give this homeowner an extra breeze on a hot summer day.

Bedrooms

The bedroom is the best place to be a little braver with your decor. It’s the place you should feel the most comfortable being yourself. Pick bolder earth tones and bring in all the natural materials to create a place that will allow you to be the best version of yourself!

This cozy room pulls out all the stops. The way the headboard coordinates with the gorgeous pendant lights has our jaws on the floor! They give the room a natural glow and highlight that warm orange wall. To some a deep, rich color like this can be intimidating, but this bedroom is the perfect example of what can happen when the risk pays off.  

Going dark on the paint can be risky, but using light, warm colors to contrast it is a clever way to combat any heaviness and create balance. The pendant above the bed is a gorgeous focal point that ties in with the wicker and wood. A fixture like this gives off soothing, soft lighting that helps to prepare yourself for a good night’s rest. 

If light and airy is more your speed, use this room as inspiration. Natural textiles bring layers of texture and interest to this bedroom that make it feel cozy and inviting. The rugs and layered blankets make this space feel lived-in without feeling cluttered. Sheer curtains allow for lots of diffused natural light for a dreamy daytime vibe, and will reflect just the right amount of light at night to create a relaxing and comfortable atmosphere.

Kitchens

No matter your kitchen’s current style, a few extra touches from nature can make it a gathering space where you’ll love to spend time preparing and sharing food with your loved ones. 

In a small space like this, details matter. The warmth in the butcher block counters and floating shelves stands out against the stark white of cabinets, creating a sense of balance without filling the space up with accessories. When space is small, a single bold choice is a great way to give it some personality – these mismatched pendants do just that! And of course, no nature-inspired space is complete without a little green. In a space full of hard lines, this pothos softens the edges just a little – and it’s perfect for the out-of-the way nook in kitchen since it won’t require much light. 

Going with darker textured cabinets was a bold move here. They almost look like they were carved straight from a mountain! In another space, they might look more industrial, but with the wicker pendant and basket, the white tiled backsplash, and the plants for accessories, it gives modern organic. The sharpness of the hard edges and metallic textures is softened by the natural textures and shapes throughout the space, like the draped pendant lighting – a smart choice that balances the design and makes it easier to see what you’re doing while you prep dinner.

This kitchen is a marriage of light and airy and organic design. The green styled cabinets are perfect for storing the most beautiful cookware and dishes. Adding fresh flowers makes a kitchen feel fresh and beautiful. However, the icing on this wedding cake is the lighting! Those cute white pendants and this kitchen are a match made in heaven. They fit the space perfectly and will give you some much-needed task lighting.

Nooks

Almost everyone has that spare corner in their home that they just can’t quite figure out what to do with. Adding a seating nook for reading or working one of our favorite tips to make a space feel cozy and welcoming. 

This little nook looks like Shangri-la in the middle of a house! Get cozy with a book and a blanket or just take a little rest here for some mid-day rejuvenation. Everything about this leans into the wildness of the natural world. Even the lighting is freeform and organic, these hanging pendants make this space feel like magic and will give you light to read no matter the time of day. 

This boho-coastal nook is just what the doctor ordered for some me-time. We love a good hammock – and this one is just begging to be relaxed in. The driftwood frame with the macrame hammock turns this space from an empty white corner into a light and airy refuge. The beaded chandelier is an unexpected twist that ties perfectly with the accessories, making this nook feel like it’s just a few steps away from the beach.

We can tell every element in this picture was chosen intentionally because it works together so well. From the wood and wicker furniture to a neutral color palette with a grounding green on the wall, you can’t get more organic than this! The dome desk lamp in white is a smart choice for task lighting – its small footprint doesn’t eat up work space, and the height and color make it pop against the dark wall behind it. This work nook may be small in size, but not in style. 

—

Using an earthy color palette and natural materials in your design is nothing short of gorgeous when it’s done well. We love this trend and want to help you create it in your home. Come visit Super Lite and show us what inspires you. We’ll help you the find the perfect lighting solutions to create your own natural sanctuary.

Home Lighting and Interior Design 101: Top Interior Design Tips From The Lighting Experts

Home Lighting and Interior Design 101: Top Interior Design Tips From The Lighting Experts

by ·

Have you ever walked through your home and wondered, “why did my stuff look cuter online/in-store?” If you have, there’s a decent chance the problem is your home lighting. Product images and store displays always have excellent lighting, showing you the best possible version of their decor, paint samples, art, and furniture. 

But if you buy that gorgeous piece or perfect paint color and put it under poor lighting, you’re bound to feel like you got duped.

Luckily, the rules to great lighting aren’t very complicated! You can start updating your home lighting for relatively low cost, low skill, and low tools. 

Consider this post a free course on home lighting essentials, including practical interior design tips from lighting experts. Answer quiz questions along the way to see if you’ve got it, then apply what you learn to make your interior design shine!

The Basics

Let’s start with a few basic terms and ideas– including five layers of great lighting and why the bulbs you use significantly impact how your home reads.

Layers of Light

You can break up your home lighting into five different categories. Once you understand how the categories work, you can mix and match them to fit your needs. Here are the five layers you should consider in each of your rooms:

  1. General/Ambient: the primary light source for the entire room.
  2. Task:  more focused light over a workspace, like a kitchen island or desk.
  3. Accent: think mood lighting; creates an atmosphere rather than light up the whole room.
  4. Decorative: it’s more about what the fixture adds to the overall design than the light it gives.
  5. Natural: working with windows (and firelight) to maximize color and space.

We’ll break down tips for working with each of these layers later on. For now, keep in mind that a well-lit room typically has five to seven light sources spread across these categories.

Question 1: Which type of lighting is most responsible for setting the mood in your space?

Warmth of Bulbs

There is so much information available on bulb temperature. The truth is you can get started with just a few pieces of information. First, bulb temperature refers to the color and brightness of the light. So let’s break it down.

Cool light will wake you up, help you focus, and is best for showing the true colors of paint, makeup, and clothing. These are the bulbs in the bottom row of the image above. Cool bulbs are great for offices, kitchens, and vanities.

Warm light has the opposite effect– it relaxes and casts a yellow or orange glow on your walls and furniture. Warm light is perfect for bedrooms, living rooms, and dining areas.

Both ends of the spectrum are important for different areas. And sometimes you might need to combine them in the same room so you can control the activity you’re doing. 

Now, let’s get into some specifics about how to work with each of our five light categories.

Question 2: Which light temperature is best for relaxing, cool or warm?

General or Ambient Light

As stated earlier, general or ambient lighting is your primary source of light for your space. It’s often centered in the ceiling so it can cast a bright, even light across the room. Your light fixture will greatly impact how the light casts. For example, flush mount domes offer little resistance to light, while metal shades will concentrate light downwards.

Since general lighting gives the most light, it will set the tone for your space. Here are a few top tips for nailing the general lighting in your home:

  • Use cool ambient lighting for kitchens, offices, and bathrooms.
  • Use warm light for living rooms, dining, and bedrooms. 
  • Swap out your builder-grade flush mount for an immediate (not to mention cheap and easy) upgrade. 

Question 3: Where should you position your general light source?

Task Lighting

Task lighting concentrates light (and your focus) on important tasks, like homework, dicing up vegetables, and filling out expense reports. They are also more obvious choices in your design since they often hang down or sit close to the action. 

Top tips:

  • Hanging pendants often look best in odd numbers, so stick to one, three, or five pendants where possible.
  • Strip lights or spotlights tap into task lighting fixtures to highlight art or displays to create design focus. 
  • Don’t forget LED strips as a versatile option! Place them around mirrors and under cabinets for steady, bright light.

Question 4: How do you know what areas need task lighting?

Accent Lighting

Accent lighting covers mood lighting and rounds out the lightscape. From reading lamps to LED strips behind TVs, they land closer to decorative lighting than really focusing on function. 

But don’t underestimate what they deliver! Accent lighting easily becomes general lighting during movies, date nights, and intimate gatherings with friends and family. 

Top tips:

  • Warm light is usually best for accent lighting. Scatter a few accent light sources around gathering places to have enough light to fill the room without the general light source.
  • Sconces are a great way to switch up typical lamps. And some come with plug-in cords– no hard wiring needed!
  • Color-changing bulbs and LEDs are a great option for accent lights. Then they are versatile for task lighting or mood lighting as the situation requires!

Question 5: True or false? If I want to add accent lights to my home, I have to hire an electrician.

Decorative Lighting

The final category is sometimes lumped in with accent lighting since they both have more to do with aesthetics than functionality. But we pulled this out to give special attention. 

Decorative lighting is about adding a super cool fixture, with the provided light taking a backseat. For example, using a chandelier for general lighting offers general light for the room, but its top priority is providing a visual “wow.”

  • Try mixing up the expected, like using pendants or sconces where you’d normally use a lamp. 
  • Get creative and turn a statue or other thrift finds into a one-of-a-kind light source.
  • Work with a local light showroom for designer-level pieces for a fraction of the price– plus top tips on installation and more!

Question 6: What is the purpose of decorative lighting?

Natural Light

Natural light is the final component of your lightscape. While manipulating natural light isn’t as easy as shopping for a great light fixture, it’s still critical to the overall feel of your home. 

For example, when shopping for paint, check the swatches day and night to see if there’s a dramatic change in appearance. This will also inform your decision on what kind of bulbs you use. And if your room’s color changes a lot from day to night, you can use cooler “daylight bulbs” to keep your color from changing as much. 

Top tips:

  • To get an airy feeling, use light curtains and hang them as close to the ceiling as you can, regardless of where your window stops. 
  • Which way do your windows face? You’ll get very different glows north versus south, as north-facing windows tend to get cooler light, with south-facing windows giving warmer light. Work with the natural light temperature when picking paint colors and decor!
  • Remember, dark colors absorb light, and lighter colors reflect it. So if you want a dark, moody space, dark paint will help to suck in extra light while still getting to keep the windows open. 

Question 7: True or false? Paint colors always look the same, no matter the time or the way windows face.

Summary

With a basic understanding of these simple lighting and interior design principles, you’re ready to convert your home from predictable and dull to vibrant and glowing! Remember:

  • You need all five layers of light to pull off a great room design.
    • General: main light source.
    • Task: focused light on important activities.
    • Accent: set the mood.
    • Decorative: dress it up, make it unexpected.
    • Natural: work the windows.
  • Bulb temperature affects concentration and color interpretation. 
    • Cool light for true colors and enhanced focus. 
    • Warm light for cozy relaxation and a golden touch to color. 
  • Updating your lighting doesn’t have to be complicated. Work with local professionals to get a leg up with great selections, expert advice, and affordable prices.

Need Help?

Proper lighting is essential to a fully functioning home– but it can be challenging to nail balanced brightness, great fixtures, and a budget! Contact the experts at Super Lite for advice on your project!

—

Quiz Answers:

Question 1: Which type of lighting is most responsible for setting the mood in your space?

General (ambient) lighting is a room’s main light source, so it’s the primary contributor to the mood.

Question 2: Which light temperature is best for relaxing, cool or warm?

Warm light naturally relaxes your brain and helps you to fall asleep. Cool light wakes up your brain for detailed work.

Question 3: Where should you position your general light source?

General lighting should come from as high and centered as possible for even light distribution.

Question 4: How do you know what areas need task lighting?

If you have an area where you perform detailed work, you should check to see if you need task lighting! Ambient lighting can provide enough light, but focused work often requires focused lighting.

Question 5: True or false? If I want to add accent lights to my home, I have to hire an electrician. 

False! There are many options for battery-operated and plug-in accent lighting.

Question 6: What is the purpose of decorative lighting?

Decorative lighting works with your decor as art, giving a unique lift to your design. It’s one more detail that helps you show off your style!

Question 7: True or false? Changing your lighting will change your paint colors.

True! All colors change with the quality of the light shining on them. Window position, time of day, and bulb temperature will all change how your paint reads.

Ceiling Fan Terminology Explained

Ceiling Fan Terminology Explained

by ·

A Helpful Glossary of Common Ceiling Fan Terms

If you’re shopping for ceiling fans and it’s starting to feel like the descriptions are written in code, don’t worry! We’re here to solve the mystery with a list of basic terms you’ll need to know when looking for the right ceiling fan.

Ceiling Fan Types

Ceiling fans are most often categorized by their motor type, mount type, and/or weather rating. 

Motors

AC and DC Motors

AC motors (alternating current motors) are the most popular ceiling fan motor. They’re typically less expensive than DC motors, which is great for budget buyers. They are relatively energy efficient, are very reliable, and come with around three to four different fan speeds. 

DC motors (direct current motors) are a newer technology and often use a remote instead of a wall switch. DC motors make a quieter, more powerful fan with more speed options and are more efficient than AC motors. 

Dual Motor

Dual motor fans have two adjustable fan heads attached to a central motor. Each head is adjustable to its own speed and angle. 

High-Velocity Motor

A high-velocity fan is a powerful fan. It produces a higher-than-normal amount of airflow, providing you with a stronger breeze. 

Mounts

Downrod/Shank/Extension Rod

The multiple terms for this accessory are purely regional, and all mean the same thing– the rod or bar installed between the ceiling and the fan. Downrods can be used in many rooms but create the most impact in rooms with high ceilings. Not only do they pull the eye upwards and make the room feel bigger, but they also bring the air circulation closer to you.

Standard Mount

This type of mounting system is for level ceilings. Standard mounts usually come with a 3- to 5-inch downrod, so the fan slightly hangs down into the space.

Hugger or Flush Mount

These are perfect for low ceilings and tall people. Huggers are mounted against the ceiling and don’t use a downrod. Depending on the ceiling height, huggers or flush mount fans can help the ceiling seem higher while keeping your air circulated and fresh.

Low-Profile Fan 

For a fan to be considered low-profile, it must hang down less than 12 inches from the ceiling. Most low-profile fans are flush mounts, but some fans with short downrods are small enough to qualify as low-profile as well.

Sloped Mount 

A sloped mount is a mounting system that includes a downrod that allows the ceiling fan to be installed on a vaulted or slanted ceiling. The base is designed to let the downrod and fan hang at an angle when mounted so that the fan will be perpendicular to the floor.

Rating

Wet Rated or Outdoor Rated Fans 

Outdoor or wet rated fans are designed to withstand direct contact with rain and snow. Carefully read the packaging of your outdoor fan because not all fans can handle the same weather exposure. If you live in a particularly wet or stormy area, you’ll need a tougher outdoor fan.

Industrial and Commercial Fans

Industrial fans have powerful motors and curved blades, and they can run continuously, making them ideal for large, open areas like warehouses and gyms. Commercial fans are heavier-duty than standard fans and more aesthetically pleasing than industrial fans. They’re commonly found in schools, businesses, and restaurants.

Ceiling Fan Measurements 

This section covers the most common measurements used to describe a ceiling fan’s function and size.

Airflow (CFM)

Cubic feet per minute (CFM) refers to the amount of air moved by a ceiling fan, using the amount of air moved per cubic foot in one minute as the metric. The higher the airflow a fan uses, the more efficient your home can be as you recycle heated or cooled air. According to Energy Star, 75 CFM is the minimum airflow of an efficient ceiling fan.  

Blade Pitch 

The pitch measures the angle of the blades compared to the ground. Fan blades are slightly angled to push the air around. (If they were parallel to the floor, they wouldn’t do much!) The angle of blade pitches typically ranges between 10 and 25 degrees, but the most efficient is from 10 to 15 degrees. 

Blade Sweep or Span 

A fan’s sweep or span measures the diameter of the circle created by the blades. You’ll need to know the span of your fan to make sure it will fit properly in your room – if it’s too large it could scrape walls or snag curtains. On the other hand, it may be distracting and look out of place if it’s too small.

Motor Speed (RPM)

Revolutions per minute (RPM) refers to the speed of the blades as they rotate, measured by how many times the blades make a complete circle in one minute. High RPM fans move more air than low RPM fans of the same size, making them more efficient. 

Watt Equivalence

Some fans will require more electrical power (watts) than others, so it’s essential to have a good understanding of how much strain your new fan will put on the existing circuit. A good rule of thumb is the longer the fan blades, the more watts it will use. Expect your fan to use 55 to 100 watts.

Weight

Residential ceiling fans typically weigh anywhere from 8 pounds to 50 pounds. Keep in mind that lightweight ceiling fans are designed to hold their weight alone. You should never add anything to a ceiling fan that wasn’t in the original kit without carefully reading the manufacturer’s instructions. Some ceiling fans allow for customizable light kits. In that case, be sure to check the packaging for how much additional weight it can hold.

Number of Speeds

Most ceiling fans will have multiple speed settings so that you can control the amount of airflow and circulation in your space. Most fans will have three speeds (slow, medium, and maximum speed). You’ll also want to see if your fan can reverse direction– this will help pull warm air down from the ceiling during the winter and help to cycle your heated air.

Dimensions

You’ll need to check several measurements to ensure your fan fits correctly in the space. For example, both depth and width can refer to the blade span (or the size of the circle the fan will make). The width can also describe how wide the individual blades are. Finally, as mentioned earlier, the downrod is the pole that connects the fan to the ceiling mount. Together, these three dimensions will tell you how much space the fan will take up.

Pro tip: All fans are designed for specific square footage, meaning that some are designed to push air through large rooms while others are for small rooms. Fans designed for bigger spaces would be disruptive in a smaller room (and vice versa). The packaging of your fan will tell you the intended size of the room, so make sure to check the square footage of the intended space and match it to the appropriate fan. 

Parts and Accessories 

The final section describes potential upgrades and customization options to consider while shopping for your ceiling fan.

Light Kits

Many fans come with a light fixture attached (called an integrated light), but some can be purchased and attached depending on the fan. There are three different light kits that you can use with your fan: uplight kits which sit on top of the fan and point upwards, branched or stemmed kits use globes or shades that point up or down, but the most common light kit is the bowl or shade kit which attaches to the bottom of the fan. Keep in mind that some ceiling fans with an integrated light may not include a bulb– you may need to purchase bulbs separately.

Remote Control

Many fans available today are remote control or smart-home compatible. A remotely controlled fan may seem like a luxury, but it’s also very practical – especially for those with extremely high ceilings! Depending on the model and features, you’ll be able to adjust the lights, fan direction, and fan speed with ease. 

Reversible Blades 

Some fans allow for their blades to spin either clockwise or counterclockwise. This functionality helps to customize airflow according to the season. For example, the blades should turn counterclockwise in the summer to push the air down (a downdraft), providing cool breezes.  The fan blades should rotate clockwise to pull air upwards (an updraft) in the winter, efficiently recycling heated air without cooling the room. You can either toggle the switch on the fan or use a remote to change the direction of the blades. 

———————-

Ready to switch out your builder-grade fan or install a new one in the place of an existing light fixture? Now that you have a reference to all of the features and parts of a ceiling fan, you can shop confidently.

If you’d like additional information, a professional opinion, or installation assistance, contact the experts at Super Lite, and we’ll make sure you get exactly what you are looking for! 

Bathroom Lighting Buying Guide

Bathroom Lighting Buying Guide

by ·

Breadmaker/Shutterstock.om

Morning routine matters. Plenty of health experts have shared their research and expertise on the topic, and it’s about time we shared ours. We are staffed with people just like you—people who sometimes wake up late and stumble out the door, who wish they had more time for the gym, who care about doing their best and getting a good start to the day.

When we wake up each morning, we want a routine that maximizes energy, increases confidence, and creates momentum for the day’s tasks. And because we work in a lighting showroom, we know how much the atmosphere of your surroundings can influence that.

Specifically, a good portion of the morning takes place in the bathroom. The ambiance (or lack thereof) in your bathroom can have a significant effect on your morning. Dingy, dim bathroom lighting hardly reflects the high energy levels our bodies experience after a full night’s sleep, nor does it lend confidence for your day. 

On the other hand, good bathroom lighting:

  • Augments your body’s natural energy 
  • Improves confidence and mood
  • Create a powerful charge for the day  
  • Aids relaxation in evenings

Wondering how to make this happen in your bathroom? Here’s a breakdown of different layers of bathroom lights, then an in-depth review of how to apply them in your space.

Lighting in Layers

Artazum/Shutterstock.com

Ideal bathroom lighting has 3 categories, or layers: general lighting, task lighting, and accent lighting. 

  1. General Lighting lights a room without help from other sources. Also called ambient lighting, it is even-spread and uniform. Can lighting is one popular option here.  A large window can also provide natural ambient light.
  2. Task Lighting addresses a specific task.  Pendant lights flanking a vanity, for example, aid in makeup application or shaving. Bathroom task lighting is usually bright and direct for full face illumination. 
  3. Accent Lighting is mostly atmospheric, often drawing attention to a high-lit or low-lit area. Think over-the-tub chandeliers, floor-lighting, etc. 

Between these three layers of bathroom light, aim to have between 70 and 80 lumens of light per square foot of bathroom space. You can calculate this by multiplying the length and width of your bathroom (including bathtub or shower), for total floor space. Determine total lumens by adding together the capacity of each bulb in the bathroom, then divide the lumen total by square footage. 

Example: Your bathroom is 10’ by 6’, which totals 60 sq. feet. You have an over-the-mirror fixture with four bulbs, each with a capacity of 1100 lumens. 4,400 lumens divided by 60 sq. ft. is 73 lumens per square foot. Plenty of light!  

General Lighting

If you’re new to the lighting game, here are four types of ambient fixtures that work well in the bathroom. Recessed lights are inserted into the ceiling itself, whereas flush lights are attached directly onto the ceiling. Semi-flush lights hang with a little space between the ceiling and the fixture, while chandeliers hang furthest from the ceiling. Let’s go through each type. 

1. Recessed (Can) Lights

Recessed lights are wonderful. They’re more difficult to add into an existing bathroom, but if you’re remodeling or building a bathroom, these are a great choice! Around the house, setting cans 3-4 feet away from walls in a 6-8 foot spaced grid pattern is a good general rule to follow.  In bathrooms, the spacing tends to be closer, at 4-5 foot apart throughout the room and in the shower. 

2. Flush Lights

The most traditional and cost-friendly option for ambient lighting, flush lights are a safe option for any space. If you already have one but worry about its dim lighting, switching to LED bulbs is a great way to fix that. Check our catalog to learn more about LED bulbs and flush fixtures.

3. Semi-Flush Lights

If you’re looking for a little extra class without going full-blown chandelier, semi-flush is for you. There’s a lot of creative variation here, and semi-flush lights are sure to improve the look and lighting of your bathroom. 

4. Chandelier

It might not seem possible in a bathroom, but trust us—it is! Upgrade your bathroom’s look by using a mini chandelier, which still accommodates an 8-foot ceiling with plenty of walking space. Chandeliers often have a 4-5 light capacity versus the traditional 2-3 bulb socket in a flush or semi flush mount, adding extra light and extra style.  

Ambient Lighting Pro Tip: Whatever fixture type you prefer, choose one that’s U.L.-rated for wet or damp locations. Bathroom lights should feature tight construction that resists condensation.

Task Lighting

Targeted lighting can greatly improve the efficiency and quality of makeup application, shaving, and similar activities. Ideally, these lights imitate natural light without creating distracting shadows, making it easier for you to do your job. Here are a few common types of task lighting for bathrooms. 

1. Pendants

These hanging lights usually flank your bathroom mirror, adding extra light at the level of your face. They come in a lot of beautiful varieties, but always choose function over form when deciding on these lights. Luckily, we offer plenty of bathroom pendant lights that accomplish both!


2. Sconces

These wall mounted lights come in several styles, such as lanterns, candles, or modern varieties. Some are meant to perform the task of up/down lighting and others are specific for shining out, more appropriately lighting your face.  The latter is the better fixture for bathroom tasks. 


3. Above Mirror Lighting

You could also consider a 2-5 bulb vanity light above the mirror.  Conveniently, some fixtures are directional, allowing you to control where the bulb shines. Just be aware that light directly above your head can cause shadows on your face.

Task Lighting Pro Tip: Mount your sconces and hang pendant lights at eye level; between 60-72” from the ground up.

Accent Lighting

In bathrooms, accent lighting comes in varied forms, depending largely on the specific functions and layout of your bathroom. Accent lighting draws attention to architecture and creates an element of awe. It also enhances the functionality of your bathroom, as with the options suggested below.

1. Toe-Kick Lights

Reduce in-the-dark stumbling by adding motion sensor lights beneath your bathroom vanity. Called “toe-kick lights”, these motion-activated lights make midnight trips to the bathroom effortless. 

2. Soffit Lighting

Most common in kitchens, soffit lighting is any kind of border or perimeter lighting, like on the tile shelf next to the bathtub in the picture above. They add a beautiful atmospheric light to the bathroom as well as enhancing functionality. 

3. Additional Sconces

Though we’ve already addressed these as task lights, when they’re placed on other walls of the bathroom, they function as accent lights. Sconces are a classy way to add décor, light, and atmosphere. 

Accent Light Pro Tip: Consider the “cleanability” of each fixture. Lighting fixtures made with a shade or fabric are harder to disassemble and clean, and may get sticky with bathroom moisture. Glass fixtures are easiest to maintain in bathrooms.

Final Thoughts

If morning routine really matters, so does bathroom lighting! For every bathroom, every style, and every budget, there is a way to start adding more light to your mornings. At Super Lite, our lighting specialists are always available to discuss your unique needs, so give us a call and we’ll help you get started. Until then, we’ll leave you with three more priceless Pro Tips for bathroom lighting.

Pro Tip: Light for Function

Not all bathrooms are a major or grand part of every home.  Some bathrooms are small and intimate like small-scaled master bathrooms, powder baths, Jack and Jill kids’ baths, pool baths… so light for the function of the bathroom. For example, pool baths are utilitarian, so a simple vanity light over the mirror would be sufficient.

Pro Tip: Pay Attention to Paint

The paint color in your bathroom influences the effectiveness of your bathroom lights.  Lighter paint tones absorb less light, making your bathroom appear brighter. Darker paint tends to absorb more light and will require more lighting fixtures/more bulbs to compensate for that paint choice. Paint sheen (high gloss, satin, flat, etc.) also influences your light. 

Pro Tip: Leveraging Light Dimmers

Wall dimmers customize the level of lighting and mood of the bathroom. As you examine fixtures, each product description specifies whether a lighting fixture is dimmable or non-dimmable. If the fixture is dimmable and takes light bulbs, be sure to purchase a bulb that is also dimmable.

3 Light Bulb Mistakes Everyone Makes And How To Avoid Them

3 Light Bulb Mistakes Everyone Makes And How To Avoid Them

by ·

Using the wrong light bulb can really make your space feel all wrong. If your room feels dark and dingy or, the opposite, harsh and cold, your light bulb may be the culprit. 

Before you buy another bulb, make sure you’re not making one of these common mistakes in your home!

Light Bulb Mistake #1
Using the Wrong Wattage

Watts refer to the amount of energy a light bulb uses. The lower the wattage, the less electricity a bulb needs to stay lit. Energy-efficient light bulbs can give off the same amount of light using fewer watts, which saves you money on your power bill!

Try_my_best/Shutterstock.com

Every light fixture has its own wattage requirements, so you’ll need to do a little sleuthing to find out what your fixture requires. 

There should be a sticker or label with the wattage limit clearly printed on it, although you might need to unscrew one of your existing light bulbs and look near the threads to find it. If you can’t find the wattage limit on your fixture, give us a call and we can help you out!

Most light fixtures have an individual bulb wattage limit (typically 45W or 60W), but there are some that have an overall limit for the entire fixture instead. For these you’ll need to add the watts together for each bulb to make sure you’re under the safety limit. 

It’s okay to use bulbs with lower watts than what your fixture calls for to save on your energy bill, but never go higher. Exceeding the wattage limit on a fixture could start a fire!

Light Bulb Mistake #2
Ignoring the Lumen Rating

A light bulb’s lumen rating will tell you how bright it is. The higher the lumen rating, the brighter it will appear. When it comes to lighting your home, different rooms need different levels of light. Work spaces need lots of light, so choosing bulbs with a high lumen rating is a great way to brighten your kitchen if it’s feeling dim. Other spaces like bedrooms and hallways don’t need to be as bright, so it’s okay to opt for bulbs with a lower lumen rating.

Luis Molinero/Shutterstock.com

There isn’t an exact formula that will tell you how lumens you need in a room, because it depends on your use and design of the space. You’ll need more lumens in work spaces like kitchens and offices, and less in bedrooms. If your design aesthetic is bright and airy or dark and moody, you’ll need to take that into account when planning your lighting. 

A good rule of thumb to get you started is 20 lumens per square foot for floors, 30 lumens per square foot for tables, and 50 lumens per square foot for desks, countertops, and task lighting. 

How does this work when you have more than one light bulb in the room? Do lumens cancel each other out or add up? The short answer is: lumens are cumulative. In a room full of furniture, light bounces around enough that the lumens don’t directly add up, and the more bulbs you use the less precise it gets. 

When you’re figuring out what you need in your home, it is 100% okay to add the lumens for each bulb in your room together to get a rough idea of what your space will need. You’ll probably end up adjusting it here and there as seasons change, when you repaint your walls, or if your use of the room changes. If your room has a lot of uses- consider getting bulbs that are dimmable so that you can change the light levels depending on what you’re doing!

Light Bulb Mistake #3
Buying the Wrong Color

If you didn’t know that light bulbs came in different color hues, now’s the time to learn! Light bulbs come in a wide range of light “temperatures”, measured in Kelvins (K). The temperature of the light you use in your room will dramatically change the way the room feels.

Suriya KK/Shutterstock.com
Warm (2,000K – 3500K) 

Wam light bulbs give a room a soft, cozy, and intimate feel with an orange or yellow hue. Outside, you see this type of light during sunrises and sunsets. Inside, it’s often associated with vintage light bulbs, like Edison bulbs, or incandescent light bulbs. It’s great for places like the living room, bedroom, and dining room.

Cool/Natural (3500K – 5000K) 

Cool or “Natural” light bulbs give off a truer white color that gives a room a clean, crisp, and inviting feel. This light is more like the light you’d see in the mornings and afternoons outdoors. It’s great for bathrooms, closets, and offices.

Daylight light bulbs (5000K – 6200K) 

Daylight light bulbs give off a light that’s close to what you’d see at noon outside on a sunny day. Daylight light makes a room feel even more clean and crisp than natural light, but it can come off a little harsh if you’re not careful. It’s a great choice for lighting work spaces like kitchens and garages, and for task lighting, like a reading lamp.

Blue (6200K+)

After 6200K light starts to look blue, so that bulbs in this color aren’t typically used in homes. There are some exceptions: some artists prefer to work under this light, and people with Seasonal Affective Disorder (SAD) may find blue light beneficial in the winter months.

Bonus Mistake #4:
Just Living With It

If the lighting just doesn’t feel right in your room, you don’t have to live with it! Too dark and depressing? Add lumens! If your clean room still feels dingy, it could be that you need cooler bulbs… or if your room feels stark and cold, you can warm up your bulbs to make it feel more inviting. And always double-check your wattage before you buy! With the right wattage, lumens, and temperature, you’ll be surprised at how much better your lighting can work for you.

We know what a big deal it is to make your house feel exactly the way you want it to. Don’t let your lighting hold you back! If you have any questions about how to find the right light bulbs for your space, give our experts a call and we’ll help you find exactly what you need!

The Ultimate Guide: How to Buy the Perfect Ceiling Fan

The Ultimate Guide: How to Buy the Perfect Ceiling Fan

by ·

A ceiling fan is a must-have fixture that will instantly beautify your space, but they also have surprising practical use. They add light and are often the centerpiece in a room, but also make a room feel more comfortable with cooler air in the summer and warmer air in the winter. 

Ceiling fans help promote health with better air circulation and improve air quality and can lower a rooms temperature by 8 degrees! Imagine the energy savings over an air conditioner even with its great benefits, heading to a big box store and grabbing the first one you see is sure to leave you disappointed. To find the right one for you, five things must be carefully considered. 

No need to worry, this ultimate guide you will discover everything you need to know to make the perfect purchase including:

  • Why the blade pitch makes all the difference
  • How to shave the most from your energy bill
  • What is that switch on my fan and how should I use it
  • How to choose the style that fits your space best
  • Getting the right size fan for your room
Here’s what you should look for when buying a ceiling fan:

1. Blade Pitch

VDB Photos/Shutterstock.com

Blade pitch refers to how steep the blades are when attached to the fan motor. Since every degree in alignment affects how much air is moved, it’s important to find the“ample pitch”. For example, a fan with a 14 degree blade pitch pushes about 80 percent more air than a fan with a 10 degree blade pitch.

Most stores only offer fans with a lower blade pitch, so consumers have to use a lot more power to get the fan to work the way they want. Not only is this very inefficient and uses much more energy than necessary, it also causes fans to burn out after just a few years and require a costly replacement.

At our showrooms, we feature fans with a blade pitch between 12 degrees and 18 degrees. This optimal range for quality ceiling fans ensures the fan will run at a low speed with silent operation. 

Plus, you won’t need to go looking for a replacement for many, many years. What’s even better? We offer a lifetime warranty on many of our ceiling fans so you can enjoy the benefits of proper air circulation for years to come.

Here at Super Lite, we pride ourselves in our state of the art showrooms to give you an idea of what your home could look like. Our lighting specialists are experienced and happy to help you find the perfect fan for your home or any space.

2. Energy Star Rating

Oasisamuel/Shutterstock.com

This is a must. Look for Energy Star-Rated ceiling fans. Energy Star fans are guaranteed to last long and save you money. When you see this logo, you know the fan has passed rigorous testing and meets the stringent standards of the EPA is made with durable and reliable parts, and works much more efficiently than non-rated alternatives. 

Think of this as a seal of authenticity. The energy star logo ensures that the materials used to build the fan are high quality and will last you much longer than comparable products. Energy Star ceiling fans provide a way to cool a space with a fraction of the standard energy usage. These fans are 20% more efficient than standard ceiling fans and come with energy efficient light kits with bulbs that last 10x longer than traditional lights. Fan motors with the Energy Star also come standard with a 30-year warranty, protecting your investment for a long, long time. 

There are some products that are worth spending a little extra money on because it will actually save you money in the long run. Ceiling fans are definitely one of those products.

Not only does Super Lite have multiple Energy Star-Rated ceiling fans to choose from, they also have over 60 years of experience and design to assist you in getting fitted with the right ceiling fan for your needs. 

3. Airflow Direction

Casper1774/Shutterstock.com

Ceiling fans can be set to rotate clockwise or counterclockwise. Why is this? It all has to do with the season. Yes, the time of year actually affects the airflow needs of a room!

If you set your fan counterclockwise, the air will be pushed directly downward. This setting is best suited for summertime when the downward airflow will give a nice cooling breeze that reaches the whole room. If your fan has a higher blade pitch, you can even reduce the “feel” temperature of the room by an entire 7 degrees!

However, during winter the hot air rises to the ceiling. Set your fan clockwise during the colder months, and it will push the air off the ceiling and out to bounce it off the walls to create a warmer feel that fills the entire room.

Super Lite can also help you install smart technology into your ceiling fixtures to make your life just a little more simple. How nice would it be to be able to control your fan with a remote or even just the command of your voice? You won’t have to worry about getting up to turn on the fan after you’ve gotten all cozied up in your bed because you can just to it with the click of a button.

4. Fan Style

Vasin Srethaphakdi/Shutterstock.com

It’s important for your fan to match the rest of your decor to tie everything together. A vintage style fan may look odd if the rest of your furniture has a more modern vibe to it. 

Be sure to explore your options in different fan styles and take the time to look into all the different colors, styles and shapes. Believe it or not but a fan can become a centerpiece and tie together a room. A ceiling fan is like the cherry on top when it comes to decor, having it match everything else just makes the room feel more complete. 

Not sure where to begin? Read through some of the most popular design styles to see what would fit best in your space:

  • Classic: These traditional styles are anything but boring. Classic fans typically have dark wood finishes, like oak or walnut and an antique bronze or pewter accents, and a timeless blade look that blends in seamlessly with your traditional-style home.
  • Modern: Often this fan is show-stopping statement piece that fit well into mid-century modern and industrial design looks. A contemporary style ceiling fan with smooth clean lines and metallic finishes are ideal. Look for fans often in a metallic finish or chrome and even matte-black, as well as fans with a sleek blade design.
  • Cottage: Classic white fans are best suited to cottage style. Look for an all-white fan including the motor casing and blades, with light metallic trim accents. 
  • Rustic: No longer reserved for cabins and outdoor spaces, many are giving their homes a lodge-like look. A rugged look with natural woods, typically accented with nickel or bronze hardware complement this home decor style.
  • Farmhouse: Sure to add instant charm to any room. In many varieties and styles, farmhouse fans are making a huge comeback. Look for a fans are made from a perfect blend of natural wood and industrial elements that use the vintage Edison-style bulbs.
  • Coastal/Driftwood: Bring the sea breeze right into your home with a nautical style ceiling fan. Inspired by the attractive colors and soothing quality of nature, fans with natural wood blades and oil-rubbed finishes do the trick. Often times these tropical-inspired fans are made from bamboo and have leaf-inspired designs complement homes near the beach and cottage-style interiors. 

Of course, most of us are thinking of just installing a ceiling fan inside, but have you considered your outdoor fan options? Picture this: you’re sitting on your porch, enjoying the weather, lemonade in hand and a nice light breeze coming from your patio ceiling fan. Sounds nice right? Don’t forget about your outdoor space when you’re looking at adding new ceiling fans to your home. 

Super Lite has plenty of different indoor and outdoor fans to match any style to offer and ensure your home decor feels right and matches. 

#5: Ceiling Fan Size

Luciano Santandreu/Shutterstock.com

When shopping for a fan, you have to get the right size to make sure it delivers on its promise. The size of the room you’re wanting to put it in is key. If you have a smaller room (like a bathroom) that you’d like to put a fan in, be sure you buy something with a smaller fan blade width to fit the space well. 

Larger areas such as bedrooms and living rooms will need a larger fan to circulate more air flow throughout the entire room. If you get a fan that’s too small and place it in a larger room, it’s not going to function quite the way you want it to. As a rule, bigger is better to ensure you get maximum airflow as the airflow drops off dramatically when you’re more than 2-3 feet outside of the blades. To ensure maximum benefit, here are some recommendations based on the size of the room and assuming you have chosen a good fan with at least 12 degree blade pitch.

Now that you know how to choose the right ceiling fan, you will be able to enjoy a unique sense of hygge that is far too often overlooked.

Visit Super Lite and let our knowledgeable staff help you discover the perfect size of fan for the room you’re decorating. 

Shop Ceiling Fans, by Room

About Us

We’re committed to offering you the best lighting and ceiling fan fixtures that will not only serve practical purposes throughout your home, but beautify it as well.

Here at Super Lite, our experts can help you find the perfect ceiling fan that’s just right for your home. Our ceiling fans have a blade pitch between 12-18 degrees which means they last longer and move more air than most box store fans. Not to mention, our fans have a lifetime warranty!

With years of experience, our lighting specialists can assist you in providing a wealth of knowledge to help you select, install, and purchase your next ceiling fan. Visit a store or view our selection online.